MENU
News
  1. Home
  2. /
  3. Steel Grades
  4. /
  5. 1045 high carbon steel 1045 steel 1045 steel properties

1045 high carbon steel 1045 steel 1045 steel properties

AISI 1045 Carbon Steel AISI 1045 Medium Carbon Steel General characteristics of Carbon Steel 1045. C1045 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. C1045 will through harden to 2.5” (63mm) with a tensile strength of 66120 Ksi (620850 MPa)

Get A Price [email protected]
  • ASTM SAE AISI 1045 Carbon Steel Heat Treatment, Chemical

    ASTM SAE AISI 1045 steel is one of the commonly used medium carbon steels with an average carbon content of 0.45%, medium tensile properties, good strength, toughness and wear resistance. It can be treated by annealing, flame treatment or induction hardening.

  • 1045 SAE 1045 AISI 1045 Steel SAE AISI 1010 1015 1020

    1045 Medium carbon steel. often used for bolts, studs and shaft parts. High strength and hardness. 1045 is medium carbon steel. The higher carbon content imparts higher strength properties than 1018. When higher degrees of dimensional accuracy and straightness are required, we recommend the use of precusuib shafting.

  • 1045 steel

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. 1045 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

  • 1045 S45C C45 Steel Properties Heat Treatment

    What is 1045 Steel? AISI 1045 steel is high quality medium carbon steel with high strength. It also can be called JIS S45C and DIN C45 steel. It is usually used in normalized condition because of its bad hardenability. It needs to be quenching and tempering treatment to get higher mechanical performance.

  • AISI 1045 Steel SAE AISI 1045 (S45C, G10450) Carbon

      Carbon steel AISI 1045 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number.

  • SAE AISI 1045 (S45C, G10450) Carbon Steel :

    SAE AISI 1045 steel is a carbon (non alloy) steel formulated for primary forming into wrought products. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number. It can have a moderately high tensile strength among the

  • 1045 medium tensile carbon steel in AISI Standard

    AISI 1045 steel is a medium carbon steel with high tensile strength and hardness. It is highly machinable and is used in wear resistant applications.

  • C1045 Carbon Steel Plates, C1045 Sheets Supplier, C1045

    High Carbon Steel C1045 Sheets, C1045 Boiler Plates, Carbon Steel C1045 Shim Sheets, Carbon Steel C1045 Circle, C1045 Cold Rolled Plates, Carbon Steel C1045 Coils, Carbon Steel C1045 Plates Dealer in India. With rich industry experience and knowledge, we are manufacturing and supplying a qualitative assortment of C1045 Sheets & Plates.

  • Grade 1045 Steel McMaster Carr

    High Strength 1045 Carbon Steel Rods and Discs Stronger than low carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts. Ground rods are decarb free for a uniform surface that will consistently accept heat treating.

  • Increased Strength and Impact with 1045 Steel

    Increased Strength and Impact with 1045 Steel Carbon steel has become one of the most widely used materials in the world, and this is thanks in large part to the 1018 and 1045 steels. Luckily, our deep inventory will meet whatever needs you may have, and our Sure Bar™ promise guarantees that our products are of the highest quality.

  • Cold Drawn 1045 Carbon Steel :MakeItFrom

    It has the highest strength compared to the other variants of SAE AISI 1045 steel. The graph bars on the material properties cards below compare cold drawn SAE AISI 1045 towrought carbon or non alloy steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set.

  • AISI 1045 Carbon Steel 1.1191 CK45 S45C steel OTAI

    ASTM AISI 1045 Steel is a medium carbon, medium tensile steel supplied as hot rolled, forged or normalized. Otai special steel supply 1045 round bar, plate, steel rods, steel bars, hexagonal bar, flat bar, square, pipe/tube. Regarding the specific dimension, please contact our professional team for any AISI 1045 Steel Round Bar.

  • C45 Round Bar AISI 1045 DIN 1.1191 JIS S45C Otai

    Steel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 – 700 Mpa and Brinell hardness range 170 – 210

  • 1045 Steel JIS S45C DIN CK45 EN8 OTAI Special Steel

    AISI 1045 steel is a kind of medium carbon steel design need more intensity and hardness can function. The steel has excellent dimensional accuracy, concentricity and straightness, common to reduce wear in high speed applications. it can form turned, ground and

Our Steel Products' Certificates:

Steels Certificates

Our Factory:

Steels factory

Packaging & shipping:

Packaging & Shipping

What Can I Do For you?